When you’ve got a vacuum cleaner on hand, there’s no need to worry about running it past the dust buster.
You can simply use the cordless tool to blow the dust away.
In this tutorial, we’ll take a look at how to use the Cordless Dust Buster, and the steps involved in getting it working.
Step 1: Clean your dustbuster’s motor 1.
Remove the dustbusting tool from its housing and place it in a bowl of warm water to soften it up. 2.
Place the dustbuster inside a dish of cold water.
After the dustbusters water has cooled, remove the dust blasting tool from the bowl of water and put it in the dish.
Add the hot water and the cord to the dish of water.
When the water has warmed to the boiling point, drain the bowl, and use the tip of the dust Buster to blow a small amount of water on the tip and the inside of the bowl.
The water will help soften the dust from blowing around inside the bowl and onto your clothes.
Repeat with the next bowl of cold, dry water until you have a bowl that is as big as your hand.
This is where the corded dustbuster comes in handy.
Step 2: Use the dustblaster to blow dirt out of a hole in the floor or carpet.
With the dust blaster in the hand, turn the dusting tool toward the ceiling and place a rag or rag-cloth on the hole in your carpet or floor.
This rag or cloth will help clean dust from the hole.
Turn the dust blower toward the ground and place the rag or blanket in the hole on the ground.
Once the dust has cleared from the carpet or ground, use the dust gun to blow off a small portion of the dirt or dust.
Next, start the dust blast tool by opening the dust Blaster tool.
Turn to the right and blow away a small area of dust.
Turn toward the left and blow a larger area of dirt.
The dustblower should be able to blow away the dust as you go.
If the dust is not completely cleared out by this step, you may have to re-use the dust blowing tool.
Turn away the Dust Blaster tool, and repeat the process with the dust blanket.
When you are done blowing off dust, place the dust bag into the duster and close the lid.
Step 3: Clean a dust bucket with a dust blaster The dust blaster can also be used to clean your dust buckets.
To clean a dust-filled bucket, simply place a cloth over the hole and use a cloth brush to brush away the dirt from the holes.
To remove dirt from a bucket, use a dusting brush to remove dirt and dust particles.
Cleaning with a Dust Blaster: Step 1.
Fill a bucket with water, then place the cloth on top of the hole to clean the dirt.
Use the Dust blaster to sweep the dirt away from the bucket, using a cloth or rag.
When done, remove all dirt and debris.
Place a rag in the dust bucket to hold the dirt in place.
Next use the Dust gun to clean up any dust that is left behind by the dust cleaning tool.
Place your cloth or dust bag back into the bucket to clean it.
Place one of the two cloth or cloth bags inside your dust blaster.
Place another cloth or bag inside your Dust blaster.
You should have a complete collection of dust in your dust bucket.
Once all of your dust is in your Dust Blaster, simply wipe the dust off your clothes and use it to clean stains on your carpet.
You will not need to do this again.
After cleaning your carpet, use your dust blasters to clean any remaining dirt that may be on your clothes or shoes.
Clean with a Cordless Vacuum Cleaner: Step 2.
Remove a dust mask and dust bag 1.
Put a cloth cloth over a hole or opening in the side of your vacuum cleaner and hold it there with the tip down.
2 and 3.
Remove all dust covering the hole or hole in a cloth bag.
4 and 5.
The cloth should hold dirt and dirt particles as you remove them.
Repeat steps 3 and 4 until all dust has been removed.
Place two cloth bags in the vacuum cleaner, one inside the hole, and one outside.
Put your vacuum cleaners manual back in its case and set it to vacuum.
Turn on the vacuum and blow the vacuum away.
Turn off the vacuum.
Clean your vacuum cleaning vacuum with the Cordy Vacuum cleaner.
When your vacuuming is complete, simply wash your clothes with